Single Port Temperature Humidity Sensor – Variable Length

Single Port Temperature Humidity Sensor – Variable Length

$225.00

Can be extended with any ethernet length cable, up to 300 feet. 

Add to Quote

Description

Single Port Temperature and Humidity Sensor

Dual sensor, 2 sensors on one port

Combining temperature and humidity into the one sensor frees up an additional intelligent sensor port on your base unit.

  • 2 variations available
  • Powered by the base unit

Additional information

Option

Single Port Temperature and Humidity Sensor

In situations where both temperature and humidity can be critical you can keep up to speed on the current conditions using this sensor. Combining temperature and humidity into the one sensor frees up an additional intelligent sensor port on your base unit.

  • Temperature and Humidity Monitoring on a single sensor port
  • Own SNMP OID for data collection via a network
  • Temperature measurement from -40ºC – +75ºC
  • Relative Humidity measurement from 0% – 100%
  • Powered by base unit, no additional power needed

Setup is simple with the sensorProbe, sensorProbe+ and securityProbe autosense function. Once plugged into the intelligent sensor port the base unit automatically detects the presence of the sensor and configures it for you.

Temperature and humidity for data center monitoring, remote sites and industrial controls.

All you need to do is set your thresholds for low and high warning and critical parameters. The built in graphing function of the base unit gives you a pattern of temperature or humidity trends over time.

Specifications

Temperature
Measurement Range -55°C to +75°C
-67°F to +167°F
Measurement Resolution sensorProbe+ series
0.1°C increments
0.2°F increments
securityProbe series
0.5ºC increments
0.9ºF increments
sensorProbe series
1ºC increments
1ºF increments
Measurement Accuracy sensorProbe+ series and securityProbe series
±0.5°C accuracy from -10°C to +75°C
±0.9°F accuracy from +14°F to +167°F
sensorProbe series
±1°C accuracy from -10°C to +75°C
±1°F accuracy from +14°F to +167°F
Humidity
Measurement range 0 to 100% Relative humidity
Resolution 1%RH increments, 0.01%RH sensor reading
Accuracy at At 25°C
Min : ±2%RH
Max : ±5% RH
Interface
Communications cable RJ-45 jack to sensor using UTP CAT5e/6 cable
Power source Powered by the base units. No additional power needed
Power Consumption Typical 17.25mWatt, 1.45mA
Maximum Cable Length Run length is 1000 feet (300 meters) with approved low capacitance shielded cable or UTP
Sensor type Semiconductor, microprocessor controlled
Dimensions 56 x 55 x 33.3 mm
Mounting DIN rail mounting
Screw mounting
Sensor count 2
Sensor count (NIST2/NIST4) 3
Important Note The fixed one foot type or THS01 are not designed to be extended. If you need to extend these sensors then you need to use the THS00 (remote type). We also do not recommend you trying to connect any of our AKCP sensors including the temperature and dual temp humidity sensors though patch panels or using the RJ-45 couplers to extend them. Please see the temperature sensors product manual or FAQ in our knowledge base for more details regarding this.
Compatability THSxx-NIST2 and THSxx-NIST4 compatible with sensorProbe+ series only

Sensor Types

Sensor is available in 2 variations:

Fixed length temperature and humidity sensor with 1ft of cable attached

Variable length temperature and humidity sensor. Ships with free 5ft CAT5 cable, user can extend up to 1,000ft.

Certification

Our Single Port Temperature/Humidity Sensor is calibrated using dedicated equipment which is calibrated according to ISO/IEC 17025 and calibrated by comparison against natural standards, natural physical constants, consensus standards, or by ratio type measurements using self-calibrating techniques.Standards incorporated to establish this comparison are NIST and NPL traceable.
Our Single Port Temperature/Humidity Sensor comply with RoHS and WEEE requirements. There is no substance to be declared.

3D View


View Separately

View Separately