$544.00
The E-opto16 is an expansion board that adds 16 opto isolated dry contact inputs and can be connected to any of the 2 RJ-45 expansion ports located on the front panel of the securityProbe base units.
| Option |
|---|
The E-opto16 is an expansion board that adds 16 opto isolated dry contact inputs to the securityProbe 5E.
The E-opto16 can be connected to any of the 4 RJ-45 expansion ports located on the front panel of the securityProbe 5E base unit using a standard CAT5 LAN cable.
The E-opto16 may also be daisy-chained using the E-Out / E-In ports on other expansion boards.
A wide variety of equipment that generates an output signal or voltage can be connected to each of the 2 wire dry contact inputs located on the back of the E-opto16 module. The (16) dry contact input LED status is displayed on the front panel.
The E-modules can be extended up to 300 meters from the securityProbe 5E base unit. There is no limit to how many E-modules can be connected to a single securityProbe 5E. It depends only on the number of sensors connected. A maximum of 500 data points can be monitored by the securityProbe 5E base unit.
A typical application for the E-opto16 would be to connect the outputs of an alarm panel to each of the 16 dry contact inputs allowing the securityProbe 5E’s full featured built in notification system to be integrated into these alarm panels, or other systems that output a voltage.
The 300 meter maximum run length is not the total run length of all of the E-Boards combined. This is each E-Boards maximum run length from either the base unit, or from each other.
Specifications
| Dimension | Size 8.5″ x 5.43″ x 1.80″ Weight 0.8 Kg |
| Expansion Port | 2x RJ-45 Expansion Ports 115.2K bps Data Transfer Rate |
| Mounting | 1U Rack Mount Standard Rack mount brackets included Compatible with AKCP’s DIN and rack mount trays |
| Power | External 7.0 – 9 VDC 3A Power Adapter Input Voltage and Current ratings : 100V~240V – 1A Typical 5.025 Watt, 0.67A |
| Status Indication | LED indication for power LED for Expansion port connectivity LED for sensor online and dry contact status |
| Components | Manufactured using highly integrated,low power surface mount technology to ensure long term reliability. |
| Operating Environment | Temp : Min. -35° C – Max. +55° C Humidity : Min. 20% – Max. 80% (Non-Condensing) |
| MTBF | 400,000 Hours |
| Inputs | 16x 2 wire dry contact inputs configured as opto-isolated 16x 2 wire dry contact inputs support up to 50 Volts DC and 80mA of current 1x RJ-45 expansion module input (E-in) |
| Outputs | 1 RJ-45 expansion module output (E-out) |
| E-Modules | * Daisy chain multiple E-modules including E-sensor8 and E-opto16 combined * Uses standard RJ-45 connections and CAT5 LAN cable * Maximum extension cable run length: 300 meters (1000 feet) * Compatible with AKCPs complete line of intelligent sensors * Connect up to 500 AKCP dry contact sensors to one securityProbe5ES * Connect up to 150 AKCP dry contact sensors to one sensorProbe+ (up to 4 expension units) |
Daisy Chainable
The E-Opto16 may also be daisychained using the E-Out / E-In Ports on other expansion boards.
The E-modules can be extended up to 300 meters from the securityProbe 5E base unit. There is no limit to how many E-modules can be connected to a single securityProbe 5E. It depends only on the number of sensors connected. A maximum of 500 data points can be monitored by the securityProbe 5E base unit.
Comparison between the E-opto16, X20, X60, IO-Digital8 and DCS15
OID’s for checking the Expansion Boards and securityProbe 5E
The OID will start with .1.3.6.1.4.1.3854.2 for checking the sensors on the expansion modules including the E-Sensor8.
This SNMPwalk command .1.3.6.1.4.1.3854.2.3.1.1 can be used for checking all of the sensors on the securityProbe 5E.
This SNMPwalk command .1.3.6.1.4.1.3854.2.2.1.1 can be used for returning the status of the expansion modules.
